Generally it is better to use Cisco switches as the interface is familier, works better than the web-driven rivals, they are more reliable and familiarity is worth money, unlike any other switch or router (with the exception of Juniper).
Goals
Broadly, create the VLAN, add and IP address to VLANs where needed, and move ports into the vlan.
Fix idle timeout
Looking at sh line vty 0 around other details I can see the idle timeout is only ten minutes. I like to change it to thirty minutes to give me more thinking time and to make the notes on this page without it logging me out.
switch>sh line vty 0
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 1 VTY - - - - - 8 0 0/0 -
Line 1, Location: "", Type: "xterm-256color"
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600
Status: PSI Enabled, Ready, Active, No Exit Banner, Ctrl-c Enabled
Automore On, Notify Process
Capabilities: none
Modem state: Ready
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
00:10:00 never none not set
This is how I change it to thirty minutes
switch>en Password: switch#conf t Enter configuration commands, one per line. End with CNTL/Z. switch(config)#line vty 0 15 switch(config-line)#exec-timeout 30 0 switch(config-line)#exit switch(config)#exit switch#disa switch>
Now the timeout is thirty minutes.
switch>sh line vty 0
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 1 VTY - - - - - 8 0 0/0 -
Line 1, Location: "", Type: "xterm-256color"
Length: 24 lines, Width: 80 columns
Baud rate (TX/RX) is 9600/9600
Status: PSI Enabled, Ready, Active, No Exit Banner, Ctrl-c Enabled
Automore On, Notify Process
Capabilities: none
Modem state: Ready
Special Chars: Escape Hold Stop Start Disconnect Activation
^^x none - - none
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
00:30:00 never none not set
Set IP address
So as to be able to telnet or SSH on (if supported) instead of using the serial console
switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)#int vlan1
switch(config-if)#ip address 192.168.1.2 255.255.255.0
switch(config-if)#exit
switch(config)#ip default-gateway 192.168.1.1
switch(config)#exit
switch#
Create VLANs
Looking at the vlan setup doesn't require enable but changing it does.
switch>sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/0/1, Gi1/0/2, Gi1/0/3
Gi1/0/4, Gi1/0/5, Gi1/0/6
Gi1/0/7, Gi1/0/8, Gi1/0/9
Gi1/0/10, Gi1/0/11, Gi1/0/12
Gi1/0/13, Gi1/0/14, Gi1/0/15
Gi1/0/16, Gi1/0/17, Gi1/0/18
Gi1/0/19, Gi1/0/20, Gi1/0/21
Gi1/0/22, Gi1/0/23, Gi1/0/24
Gi1/0/25, Gi1/0/26, Gi1/0/27
Gi1/0/28, Gi1/0/29, Gi1/0/30
Gi1/0/31, Gi1/0/32, Gi1/0/33
Gi1/0/34, Gi1/0/35, Gi1/0/36
Gi1/0/37, Gi1/0/38, Gi1/0/39
Gi1/0/40, Gi1/0/41, Gi1/0/42
Gi1/0/43, Gi1/0/44, Gi1/0/45
Gi1/0/46, Gi1/0/47, Gi1/0/48
Gi1/0/49, Gi1/0/50, Gi1/0/51
Gi1/0/52
1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
At this point everything is in VLAN1, which is the default configuration. However our goal here is to put ports into a relevant VLAN and turn off VLAN1. First we need to create some VLANs. Go into enable mode and conf t.
switch>en Password: switch#conf t Enter configuration commands, one per line. End with CNTL/Z. switch(config)#vlan 30 switch(config-vlan)#name servers switch(config-vlan)#exit switch(config)#exit switch#
Setup trunk to Switch 2
switch#conf t Enter configuration commands, one per line. End with CNTL/Z. switch(config)#int gi1/0/4 switch(config-if)#switchport trunk encapsulation dot1q switch(config-if)#switchport mode trunk switch(config-if)#switchport trunk allowed vlan remove 1-4094 switch(config-if)#switchport trunk allowed vlan add 30,40 switch(config-if)#exit switch(config)#exit switch#
Setup trunk to Switch 1
switch2#conf t Enter configuration commands, one per line. End with CNTL/Z. switch2(config)#int gi1/0/6 switch2(config-if)#switchport trunk encapsulation dot1q switch2(config-if)#switchport mode trunk switch2(config-if)#switchport trunk allowed vlan remove 1-4094 switch2(config-if)#switchport trunk allowed vlan add 30,40 switch2(config-if)#exit switch2(config)#exit
This config can now be seen with sh run (only pasting the relevant section)
switch2#sh run ! interface GigabitEthernet1/0/1 switchport trunk encapsulation dot1q switchport trunk allowed vlan 30,40 switchport mode trunk !