314
edits
Proper content added
(First save) |
(Proper content added) |
||
| Line 1: | Line 1: | ||
Generally it is better to use Cisco switches as the interface is familier, works better than the web-driven rivals, they are more reliable and familiarity is worth money, unlike any other switch or router (with the exception of Juniper). | Generally it is better to use Cisco switches as the interface is familier, works better than the web-driven rivals, they are more reliable and familiarity is worth money, unlike any other switch or router (with the exception of Juniper). | ||
=== Goals === | |||
Broadly, create the VLAN, add and IP address to VLANs where needed, and move ports into the vlan. | |||
== Fix idle timeout == | |||
Looking at <i>sh line vty 0</i> around other details I can see the idle timeout is only ten minutes. I like to change it to thirty minutes to give me more thinking time and to make the notes on this page without it logging me out. | |||
<nowiki>switch>sh line vty 0 | |||
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int | |||
* 1 VTY - - - - - 8 0 0/0 - | |||
Line 1, Location: "", Type: "xterm-256color" | |||
Length: 24 lines, Width: 80 columns | |||
Baud rate (TX/RX) is 9600/9600 | |||
Status: PSI Enabled, Ready, Active, No Exit Banner, Ctrl-c Enabled | |||
Automore On, Notify Process | |||
Capabilities: none | |||
Modem state: Ready | |||
Special Chars: Escape Hold Stop Start Disconnect Activation | |||
^^x none - - none | |||
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch | |||
00:10:00 never none not set</nowiki> | |||
This is how I change it to thirty minutes | |||
<nowiki> | |||
switch>en | |||
Password: | |||
switch#conf t | |||
Enter configuration commands, one per line. End with CNTL/Z. | |||
switch(config)#line vty 0 15 | |||
switch(config-line)#exec-timeout 30 0 | |||
switch(config-line)#exit | |||
switch(config)#exit | |||
switch#disa | |||
switch></nowiki> | |||
Now the timeout is thirty minutes. | |||
<nowiki> | |||
switch>sh line vty 0 | |||
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int | |||
* 1 VTY - - - - - 8 0 0/0 - | |||
Line 1, Location: "", Type: "xterm-256color" | |||
Length: 24 lines, Width: 80 columns | |||
Baud rate (TX/RX) is 9600/9600 | |||
Status: PSI Enabled, Ready, Active, No Exit Banner, Ctrl-c Enabled | |||
Automore On, Notify Process | |||
Capabilities: none | |||
Modem state: Ready | |||
Special Chars: Escape Hold Stop Start Disconnect Activation | |||
^^x none - - none | |||
Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch | |||
00:30:00 never none not set | |||
</nowiki> | |||
== Create VLANs == | |||
Looking at the vlan setup doesn't require enable but changing it does. | |||
<nowiki> | |||
switch>sh vlan | |||
VLAN Name Status Ports | |||
---- -------------------------------- --------- ------------------------------- | |||
1 default active Gi1/0/1, Gi1/0/2, Gi1/0/3 | |||
Gi1/0/4, Gi1/0/5, Gi1/0/6 | |||
Gi1/0/7, Gi1/0/8, Gi1/0/9 | |||
Gi1/0/10, Gi1/0/11, Gi1/0/12 | |||
Gi1/0/13, Gi1/0/14, Gi1/0/15 | |||
Gi1/0/16, Gi1/0/17, Gi1/0/18 | |||
Gi1/0/19, Gi1/0/20, Gi1/0/21 | |||
Gi1/0/22, Gi1/0/23, Gi1/0/24 | |||
Gi1/0/25, Gi1/0/26, Gi1/0/27 | |||
Gi1/0/28, Gi1/0/29, Gi1/0/30 | |||
Gi1/0/31, Gi1/0/32, Gi1/0/33 | |||
Gi1/0/34, Gi1/0/35, Gi1/0/36 | |||
Gi1/0/37, Gi1/0/38, Gi1/0/39 | |||
Gi1/0/40, Gi1/0/41, Gi1/0/42 | |||
Gi1/0/43, Gi1/0/44, Gi1/0/45 | |||
Gi1/0/46, Gi1/0/47, Gi1/0/48 | |||
Gi1/0/49, Gi1/0/50, Gi1/0/51 | |||
Gi1/0/52 | |||
1002 fddi-default act/unsup | |||
1003 trcrf-default act/unsup | |||
1004 fddinet-default act/unsup | |||
1005 trbrf-default act/unsup | |||
</nowiki> | |||
At this point everything is in VLAN1, which is the default configuration. However our goal here is to put ports into a relevant VLAN and turn off VLAN1. First we need to create some VLANs. Go into enable mode and conf t. | |||
<nowiki> | |||
switch>en | |||
Password: | |||
switch#conf t | |||
Enter configuration commands, one per line. End with CNTL/Z. | |||
switch(config)#vlan 2 | |||
switch(config-vlan)#name dmz | |||
switch(config-vlan)#exit | |||
switch(config)#exit | |||
switch#</nowiki> | |||